Part List, Metric Units

 

Imperial inch dimensions

Part No.	Quantity	Description	Page / Drawing
Blade		Hub D1 D2 D3
B-1	3	Metal Foil 5 X 100 cm (window flashing) or 1 roll stainless tape, 5 cm x 3 m cut in 3rds, or copper foil	p 17
B-2	1	Spaceing block: 2 cm thick plywood 14 X 14 cm	p 19, D2, 3
B-3	6	pulley centering blocks: 1.3 cm thick plywood, cut to fit	p 19, D2
B-4	2	Ball bearings: 2.22 cm ID and cam locks: Fafnir GRA014 RRB or sealed SBPF205-14 7/8	p 19
B-5	1	Blade Balance Kit	p 20
B-6	1	Plans	download
B-7	3	Blades: wood 8.9 cm X 3.8 cm X 1.37 m	p 14, D2, 3
B-8	1	Plywood backplate triangle 2 cm X 34.29 cm	p 17, D2, 3
B-9	1	Tin face plate triangle 1.5 mm X 34.3 cm	p 17, D2, 3
B-10	15	Stainless Steel (obo), Round Head Machine Screws: M8 x 1.25 X 7.5 w/nut, flat,& lock	p 18, D2, 3
B-11	3	Hot dip galv. carriage bolts: M14 x 2 X 14 w/nut, & lock	p 18, D2, 3
B-12	2	3 Hole pressed flange bearing mounts and 2 grease zerks (grease nipples): Fafnir G52MSA	p 18, D2, 3
B-13	1	pulley: 25.4 cm Outside Diameter x 2.54 cm Inside Diameter, aluminium, "A"-pitch Source	p 18, D2, 3
B-14	1	V Belt: 0.95 x 104.14 cm outside length, "A"-pitch	p 18, D2, 3
B-15	3	Flat Head wood screws: 5.5 mm X 20 mm	p 18, D2, 3
Feathering gizmo		D1 D2
C-1	1	Blade shaft: 15 mm Inside dimension galvanized water pipe X 30 cm"	D1, 2
C-2	3	Iron angle frame brackets: 19.5 cm long, X 7.6 cm leg, X 0.3 cm thick (+/-)	D1, 2
C-3	1	Alternator bracket: iron 6 mm X 5 cm X 20 cm	D1, 2
C-4	1	Rest arm. hardwood, 2.2 cm X 4 cm X 19 cm	D1, 2
C-5	1	Feathering Lever: hardwood 2.22 cm X 2.5 cm X (about) 33 cm"	D1, 2
C-6	1	Stainless Axle (Feathering pivot): 10 mm X 250 mm, with 2, 3.5 mm X 19 mm cotter pins	D1, 2
C-7	1	Alternator mounting pin, Iron, 10 mm X 100 mm rod	D1, 2
C-8	1	Belt tension adjustor, iron, 10 mm X 180 mm eye bolt	D1, 2
C-9	5	U-bolt: 14 mm cable clamp and 2 - M14 x 2 nut each	D1, 2
C-10	4	Hex head bolt 5 cm X M11 x 1.5 with nut and lock each	D1, 2
C-11	2	Machine screw M7 x 0.1 X 5 cm, with nut & lock	D1, 2
C-12	1	Pull spring 2.50 cm X 30 cm	D1, 2
C-13	2	Bushings 10 mm Inside Diameter X 17 mm Outside Diameter X 1.6 cm long, (Kingman K-68-6)	D1, 2
C-14	4	14 mm Inside diameter flat washers	D1, 2
C-15	1	Wood screw eye: 0.5 mm X 5 cm	D1, 2
C-16	1	Stainless cable 120 cm X 1.25 mm, 2 swage clamps	D1, 2
C-17	1	Cable swivel	D1, 2
C-18	1	Cotter Pin: 1.25 mm x 4 cm (or a piece of wire)	D1, 2
C-19	1	Cap screw: M14 x 2 X 2 cm	D1, 2
Frame		Bottom D1 D2 D3
F-1	1	Tail vane arm: wood, M14 x 2 6.4 cm X 3.8 cm X 1.515 m	D1, 3
F-2	2	wood blocks: 3.8 cm X 5.72 cm X 28 cm	D1, 3
F-3	2	5 cm X 2.2 cm X 48.3 cm hardwood	D1, 3
F-4	1	Tail Vane, Sheet metal 25 cm X 92 cm X 1.5 mm thick, Plywood works too.	D1, 3
F-5	2	Machine screws M7 x 0.1 X 7.6 cm with flat & nut each	D1, 3
F-6	2	Carriage bolts: 10 mm X 25.5 cm with 2 flat washers, 1 lock,1 nut each	D1, 3
F-7	2	Machine screws: Round head, M7 x 0.1 X 6.4 cm with 2 flat, 1 lock & 1 nut each	D1, 3
F-8	1	Galv. awning pulley for 3 mm wire (or wrapped coil for a bicycle brake cable)	D1, 3
F-9	1	Flat Head wood screw, 5.5 mm X 30 mm	D1, 3
Turntable
T-1	3	Pipe flange for a 25 mm (Inside diameter) pipe	D1, 3
T-2	4	Bolts M11 x 1.5 X 6 cm with 1 flat, lock and nut each long	p 11, D1, 3
T-3	1	Water pipe 25 mm Inside Diameter X 40 cm long	p 4, D1, 3
T-4	1	Water pipe 32 mm Inside Diameter X 40.6 cm long	p 7, D1, 3
T-5	1	copper tube: 14 mm outside diameter x 6.5 cm long	p 6, D1, 3
T-6	1	Vinyl tube: 10 mm x 50 cm long	D1, 3
T-7	3	Stainless hose clamp 12 - 15 cm diameter	D1, 3
T-8	1	20 mm copper pipe section: 6 cm long x 1.65 mm wall thickness	p 4, D1, 3
T-9	1	20 mm copper pipe section: 4.5 cm long x 1.65 mm wall thickness	p 4, D1, 3
T-10	1-1/2	20 mm Inside diameter plastic pipe drilled to 23 mm ID X 26 0D, 4.75 cm long	p 4, D1, 3
Electrical
E-1	1	metric size 10 multistrand copper wire, 112 cm long, PVC electrical insulation	p 4, D1, 3
E-2	1	metric size 2.5 multistrand copper wire, 112 cm long, PVC electrical insulation	p 4, D1, 3
E-3	1	metric size 10 multistrand copper wire: 53.5 cm long, PVC electrical insulation	p 11, D1, 3
E-4	3	Wood block insulator: 10 cm X 3.2 cm X 3.8 cm	p 5, D3
E-5	3	Stainless hose clamps: 6.5 cm diameter	D3
E-6	2	Brass (automotive shim) wipers: 0.32 mm x 1.3 cm X 7.6 cm	p 5, D3
E-7	2	Brass RH machine screws M7 x 1 X 40 mm, nut, flat ea.	p 5, D3
E-8	4	Ring terminal 6.5 mm hole, for metric size 10 wire	D3
E-9	2	Ring terminal 5 mm hole, 2.5 mm wire	D3
E-10	2	Female push-on connectors, 2.5 mm wire	D3
E-11	1	Chrysler alternator 12 V, 42 amp, single field, model 7000	D1, 2, 3
E-12	1	Voltage regulator for same alternator	D3
E-13	1	Mercury switch (wikipedia), or Float switch, or bilge pump switch. DIY mechanical switch: 1 metal strip 1.6 cm x 25 cm x 1.5 mm thick, 3 round head wood screws 13 mm X 5 mm, 1 metal angle, 2 cm X 2 cm x 1.5 mm thick, 30 mm brass machine screw, size M8 x 1.25, 2 nuts	D3 D2
E-14	1	Manual on-off switch rated 5 amp 12 V	D3
E-15	1	3 Amp bus fuse and clip for 2.5 mm field wire	D3
E-16	1	0-50 Ammeter	D3
E-17	1	Battery level indicator (0-16 volt meter)	D3
E-18	1	Mercury switch clamp	D3
E-19	1	Diode, 200v, .5 mfd	D2, 3